If the electronic system detects the presence malfunction, the code is displayed on the screen faults in the form of a symbol and a letter denoting the faulty component. Under certain conditions, in addition to display of the malfunction code, the corresponding warning lamp flashes and turns on sound signal. If a malfunction occurs in the system, an error code appears on the dashboard corresponding to the malfunction. In the event of a malfunction, all codes can be viewed using the Instrument Panel Control Unit on the instrument cluster. Emergency operation is activated, in which the engine power is limited to 60%, and the maximum speed is 1500 rpm.
System fault E3 engine with AdBlue / DEF technology
Depending on the displayed fault it is recommended to perform basic operations service or contact your dealer (see fault code tables below).
Massey Ferguson MF8925 Error Code
System errors | |||||
GPI Error No. |
Checked signal from |
Type of Error |
Error LED flash code |
DIA 1 Error No. |
Error caused by |
1 | sensor supply voltage | 4 | – • • • | 01 | sensor voltage out of range |
2 – 16 | not used | ||||
Sensor errors | |||||
GPI Error No. |
Checked signal from |
Type of Error |
Error LED flash code |
DIA 1 Error No. |
Error caused by |
1 | default parameter checksum |
3 | –––––– | 17 | checksum mismatch |
2 | inch parameter checksum |
18 | included default checksum |
||
3 | inch/brake potentiometer |
7 5 6 | – – • • | 19 | no pedal setup done value too low value too high |
4 | engine speed pickup | 6 | • • – • | 20 | engine speed missed when starting engine |
5 | propel current | 1 2 |
– • – • | 21 | short cut open circuit |
6 | F-N-R switch | 4 | • – – • | 22 | short cut between forward and reverse |
7 | engine speed pickup | 6 | – – – • | 23 | engine speed interrupted |
8 | hydro motor propel current |
1 2 | • • • – | 24 | short cut open circuit |
9 | creep drive parameter checksum |
25 | included default checksum |
||
10 | creep drive potentiometer |
5 6 | – • • – | 26 | value too low value too high |
11 | motor speed pickup | 6 | • • – – | 27 | motor speed interrupted |
12 – 32 | not used | ||||
– | wrong kernel | – | • – • – | kernel software < 2.5 | |
– | wrong hardware | – | – – • – | hardware is not S1X-11 G2 AMP |
Massey Ferguson 8450-8460-8470-8480, 8600-8650-8660-8670-8680-8690 Fault Codes dashboard
code | Description | Solution |
D101 | Armrest connection not detected | Check the connection under the vile boiler |
D121 | Generator regulator | Please contact your dealer. |
D122 | Generator regulator | Please contact your dealer. |
D127 | Fuel gauge | Please contact your dealer. |
D128 | Fuel gauge | Please contact your dealer. |
D129 | Too high voltage battery baht yards |
Please contact your dealer. |
D130 | Battery voltage too low bata peu |
Make sure the battery terminals are secure and free from dirt. Please contact your dealer. |
D133 | Accelerator Pedal Potentiometer | Please contact your dealer. |
D134 | Accelerator Pedal Potentiometer | Please contact your dealer. |
D135 | Power Control Controller | Please contact your dealer. |
D136 | Power Control Controller | Please contact your dealer. |
D137 | Armrest Lever Potentiometer | Please contact your dealer. |
D138 | Armrest Lever Potentiometer | Please contact your dealer. |
D139 | Clutch pedal | Please contact your dealer. |
D140 | Clutch pedal | Please contact your dealer. |
D141 | Engine speed signal | Please contact your dealer. |
D142 | High clutch point sensor | Please contact your dealer. |
D143 | Low clutch point sensor | Please contact your dealer. |
D144 | Power Control Controller | Please contact your dealer. |
D145 | Power Control Controller | Please contact your dealer. |
D146 | Power Control Controller | Please contact your dealer. |
D147 | Power Control Controller | Please contact your dealer. |
D148 | dashboard | Please contact your dealer. |
D149 | CAN bus signals | Please contact your dealer. |
D150 | CAN bus signals | Please contact your dealer. |
D151 | Tractor speed too high | Please contact your dealer. |
D152 | dashboard | Please contact your dealer. |
D153 | dashboard | Please contact your dealer. |
D154 | Autotronic 4 CAN bus communication with instrument panel | Please contact your dealer. |
D155 | dashboard | Please contact your dealer. |
D156 | High clutch point sensor | Please contact your dealer. |
D157 | Engine speed sensor | Please contact your dealer. |
D158 | Armrest Lever Potentiometer | Please contact your dealer. |
D159 | Power Control Controller | Please contact your dealer. |
D160 | Power Control Controller | Please contact your dealer. |
D164 | Communication error on the CAN bus of the EEM system with the instrument panel | Please contact your dealer. |
D170 | Throttle grip | Please contact your dealer. |
D181 | Auxiliary Hydraulic Lever | Please contact your dealer. |
D182 | Auxiliary Hydraulic Lever | Please contact your dealer. |
D183 | Wheel Angle Sensor | Please contact your dealer. |
D184 | Wheel Angle Sensor | Please contact your dealer. |
D185 | Keyboard | Please contact your dealer. |
D186 | Keyboard | Please contact your dealer. |
D189 | Output voltage 9.5V | Please contact your dealer. |
D190 | Output voltage 9.5V | Please contact your dealer. |
D191 | Air pressure sensor | Please contact your dealer. |
D192 | Air pressure sensor | Please contact your dealer. |
D193 | Steering gear ratio quick change potentiometer | Please contact your dealer. |
D194 | Steering gear ratio quick change potentiometer | Please contact your dealer. |
D195 | Internal temperature sensor instrument panel | Please contact your dealer. |
D196 | Internal temperature sensor instrument panel | Please contact your dealer. |
D197 | Auxiliary Hydraulic Oil Temperature Gauge | Please contact your dealer. |
D198 | Auxiliary Hydraulic Oil Temperature Gauge | Please contact your dealer. |
Engine error codes
code | Description | Solution |
E91 | Malfunction of throttle position sensor flap |
Please contact your dealer. |
E94 | Fuel filter pressure | Check the fuel level in the tank. Check the fuel lines for damage. Check the condition of the filter (date of last service). Check the electrical fuel priming pump is working (check the fuse). Please contact your dealer. |
E97 | Water in fuel | Check for water in the fuel system sump. Please contact your dealer. |
E100 | Oil pressure | Check the oil level. Please contact your dealer. |
E102 | Boost pressure | Check the condition of the air filter. Check the condition of the suction hoses. Please contact your dealer. |
E105 | Intake Manifold Temperature | Check the condition of the radiators. Check the condition of the ventilation grilles. Please contact your dealer. |
E107 | Air filter pressure | Check the condition of the air filter. Please contact your dealer. |
E110 | Coolant temperature | Check the coolant level . Check the condition of the ventilation grilles. Check the condition of the radiator. Please contact your dealer. |
E157 | Fuel rail pressure | Please contact your dealer. |
E168 | Battery voltage | Check battery connections. Please contact your dealer. |
E174 | Fuel temperature | Please contact your dealer. |
E175 | Engine oil temperature | Check the coolant level . Check the condition of the radiator. Please contact your dealer. |
E190 | Engine speed signal | Please contact your dealer. |
E626 | Heater air control | Please contact your dealer. |
E629 | EEPROM error | Please contact your dealer. |
E898 | Required speed out of range | Please contact your dealer. |
E1136 | ECU temperature sensor malfunction | Please contact your dealer. |
E1378 | Changing the engine oil: too long time has elapsed |
Please contact your dealer. |
E9006 | Faulty CAN-bus of the tractor | Please contact your dealer. |
E9008 | Defective CAN ID module | Please contact your dealer. |
E9010 | External pressure | Please contact your dealer. |
E9021 | Failure of 5V DC power supply | Please contact your dealer. |
E9022 | Failure of 5V DC power supply | Please contact your dealer. |
E9023 | Failure of 5V DC power supply | Please contact your dealer. |
E9024 | Water in fuel sensor | Please contact your dealer. |
E9025 | Self-test disconnect lines | Please contact your dealer. |
E9026 | Self-test disconnect lines | Please contact your dealer. |
E9027 | Self-test disconnect lines | Please contact your dealer. |
E9030 | Short circuit in the main relay 1 ECU | Please contact your dealer. |
E9031 | Short circuit in the main relay 2 ECU | Please contact your dealer. |
E9032 | Short circuit in the main relay 3 ECU | Please contact your dealer. |
E9033 | Defective ECU shutdown function | Please contact your dealer. |
E9034 | ECU shutdown function did not work the previous time |
Please contact your dealer. |
E9035 | Normal recovery of performance | Please contact your dealer. |
E9036 | Full reboot in 2 seconds after 3 restore operations | Please contact your dealer. |
E9070 | Engine speed signal | Please contact your dealer. |
E9071 | Engine speed signal | Please contact your dealer. |
E9072 | Crankshaft speed sensor | Please contact your dealer. |
E9080 | Camshaft speed sensor | Please contact your dealer. |
E9081 | Camshaft speed sensor | Please contact your dealer. |
E9082 | Camshaft speed sensor | Please contact your dealer. |
E9083 | Camshaft speed sensor | Please contact your dealer. |
E9090 | Engine speed signal estimation error | Please contact your dealer. |
E9100 | Protection update error | Please contact your dealer. |
E9107 | Incorrect ECU address selection | Please contact your dealer. |
E9131 | Malfunction of the fuel injector No. 1 | Please contact your dealer. |
E9132 | Malfunction of the fuel injector No. 2 | Please contact your dealer. |
E9133 | Malfunction of the fuel injector No. 3 | Please contact your dealer. |
E9134 | Malfunction of the fuel injector No. 4 | Please contact your dealer. |
E9135 | Malfunction of the fuel injector No. 5 | Please contact your dealer. |
E9136 | Malfunction of the fuel injector No. 6 | Please contact your dealer. |
E9150 | Fuel rail pressure | Please contact your dealer. |
E9151 | Fuel rail pressure limiter | Please contact your dealer. |
E9152 | Fuel filter pressure | Check the fuel level in the tank. Check the fuel lines for damage. Please contact your dealer. |
E9153 | Fuel filter pressure | Check the fuel level in the tank. Check the fuel lines for damage. Please contact your dealer. |
E9170 | Fuel priming pump control (ECU) | Please contact your dealer. |
E9171 | Preheating device control | Please contact your dealer. |
E9172 | Starter relay control | Please contact your dealer. |
E9173 | Starter relay control | Please contact your dealer. |
E9174 | MPROP pump control | Please contact your dealer. |
E9230 | Inconsistency of technical characteristics of the engine | Please contact your dealer. |
E9231 | Engine Serial Number Mismatch | Please contact your dealer. |
E9233 | Module ID | Please contact your dealer. |
E9234 | Module ID | Please contact your dealer. |
E9235 | Module ID | Please contact your dealer. |
E9236 | Module ID | Please contact your dealer. |
E9237 | Module ID | Please contact your dealer. |
E9238 | Module ID | Please contact your dealer. |
E9239 | Module ID | Please contact your dealer. |
E9240 | Module ID | Please contact your dealer. |
E9241 | Module ID | Please contact your dealer. |
E9242 | The generated traversal time has elapsed | Please contact your dealer. |
E9243 | The maximum time for bypassing the computer has elapsed | Please contact your dealer. |
E9244 | Module ID | Please contact your dealer. |
E9303 | Malfunctioning cruise control | Please contact your dealer. |
E9304 | There is no data on the speed of the tractor | Please contact your dealer. |
E9305 | Incorrect digital input configuration | Please contact your dealer. |
E9306 | PTO input signal error | Please contact your dealer. |
E9310 | Fault external digital input | Please contact your dealer. |
E9311 | Fault external digital input | Please contact your dealer. |
E9312 | Torque control input | Please contact your dealer. |
E9317 | Data manager missing | Please contact your dealer. |
E3 engine error codes with technology AdBlue / DEF
U 168 | Battery voltage | Please contact your dealer. |
U 441 – U 442 – U 697 |
Catalyst temperature | Please contact your dealer. |
U 698 | Discharge heating power supply | Please contact your dealer. |
U 699 | Intake manifold heating power supply | Please contact your dealer. |
U 700 | Heating supply of the pressure pipeline | Please contact your dealer. |
U 1079 | Sensor supply voltage 1 | Please contact your dealer. |
U 1080 | Sensor supply voltage 2 | Please contact your dealer. |
U 1387 | Urea pressure | Please contact your dealer. |
U 1388 | Urea pressure sensor | Please contact your dealer. |
U 1485 | Main relay | Please contact your dealer. |
U 1677 | Modular heater | Please contact your dealer. |
U 1761 | Level sensor in urea tank | Please contact your dealer. |
U 2854 – U 2858 | CAN receiver | Please contact your dealer. |
U 2859 | Urea / Heater or Exhaust Measurement State | Please contact your dealer. |
U 2860 – U 2871 | CAN message | Please contact your dealer. |
U 2872 | Error turning on the heater or data control unit | Please contact your dealer. |
U 3031 | Temperature sensor in urea tank | Please contact your dealer. |
U 520201 | Power module temperature | Please contact your dealer. |
U 520228 | NOx emission control | Please contact your dealer. |
U 520239 | Heater power supply | Please contact your dealer. |
U 520243 | Urea level | Please contact your dealer. |
U 520257 | Leakage of urea | Please contact your dealer. |
U 520260 | Urea pressure | Please contact your dealer. |
U 520276 | Power supply voltage | Please contact your dealer. |
U 520296 | NOx control unit | Please contact your dealer. |
U 520308 | NOx sensor | Please contact your dealer. |
U 520310 | Temperature in the urea tank | Please contact your dealer. |
Transmission error codes
T4107 | Transmission oil high pressure sensor malfunction | Please contact your dealer. |
T4108 | Included range sensor malfunction | Please contact your dealer. |
T4124 | Parking brake sensor malfunction | Please contact your dealer. |
T4128 | Transmission control unit malfunction | Use the transmission protection mode. Please contact your dealer. |
T412A | Malfunction of the sensor of the estimated gear speed | Use the transmission protection mode. Please contact your dealer. |
T412B | Malfunction of the switch of ranges of high / low speeds (“Hare” / “Turtle”) | Please contact your dealer. |
T4131 | Malfunction of the summing shaft speed sensor | Use the transmission protection mode . Please contact your dealer. |
T4142 | Malfunction of the summing shaft speed sensor | Use the transmission protection mode. Please contact your dealer. |
T4144 | Malfunction of the engine speed sensor | Use the transmission protection mode. Please contact your dealer. |
T4145 | Malfunction of the sensor of the estimated gear speed | Use the transmission protection mode. Please contact your dealer. |
T4150 | Transmission filter clogging sensor malfunction | Please contact your dealer. |
T4153 | High transmission oil temperature | Further movement is prohibited. Please contact your dealer. |
T4156 | Transmission filter clogging sensor malfunction | Please contact your dealer. |
T4158 | Transmission slip sensor malfunction | Please contact your dealer. |
T4159 | Malfunction of turning on the transmission protection mode or an error in this mode |
Please contact your dealer. |
T4161 | Malfunction of the solenoid valve of the low speed range (“Turtle”) | Use the transmission protection mode. Please contact your dealer. |
T4162 | High speed range solenoid valve malfunction (“Hare”) | Use the transmission protection mode. Please contact your dealer. |
T4163 | Malfunction of the solenoid valve for speed limiting up to 30 km / h | Please contact your dealer. |
T4164 | Defective clutch solenoid valve | Please contact your dealer. |
T4172 | Transmission filter clogging sensor malfunction | Please contact your dealer. |
T4173 | Transmission oil temperature sensor malfunction | Please contact your dealer. |
T4174 | Parking brake sensor malfunction | Please contact your dealer. |
T4182 | Malfunction of the calculated gear speed sensor Malfunction of the summing shaft speed sensor |
Use the transmission protection mode. Please contact your dealer. |
T4183 | Malfunction of the calculated gear speed sensor Malfunction of the summing shaft speed sensor |
Use the transmission protection mode. Please contact your dealer. |
T4192 | Malfunction of the switch of the right brake | Please contact your dealer. |
T4193 | Left Brake Switch Malfunction | Please contact your dealer. |
T41A0 | Transmission control unit malfunction | Please contact your dealer. |
T41A1 | Transmission control unit malfunction | Please contact your dealer. |
T41A2 | Transmission control unit malfunction | Please contact your dealer. |
T41A3 | Transmission control unit malfunction | Please contact your dealer. |
T41A4 | Transmission control unit malfunction | Please contact your dealer. |
T41A5 | Transmission control unit malfunction | Please contact your dealer. |
T41A6 | Transmission control unit malfunction | Please contact your dealer. |
T41B0 | CAN bus malfunction | Please contact your dealer. |
T41B1 | Malfunction of the solenoid valve of the low speed range (“Turtle”) | Please contact your dealer. |
T41B2 | High speed range solenoid valve malfunction (“Hare”) | Please contact your dealer. |
T41C1 | Engine stalled due to transmission overload | Reduce the load on the transmissions and try again. Please contact your dealer. |
T41D1 | Calibration error | Please contact your dealer. |
T41D2 | Calibration error | Please contact your dealer. |
T41D3 | Calibration error | Please contact your dealer. |
T41D4 | Calibration error | Please contact your dealer. |
T41D5 | Calibration error | Please contact your dealer. |
T41D6 | Calibration error | Please contact your dealer. |
T41D7 | Calibration error | Please contact your dealer. |
T41D8 | Calibration error | Please contact your dealer. |
T41D9 | Calibration error | Please contact your dealer. |
T41DA | Calibration error | Please contact your dealer. |
T41DB | Calibration error | Please contact your dealer. |
T41DC | Calibration error | Please contact your dealer. |
T41DD | Calibration error | Please contact your dealer. |
T41DE | Calibration error | Please contact your dealer. |
T41DF | Calibration error | Please contact your dealer. |
T41 E0 | Defective clutch solenoid valve | Please contact your dealer. |
T41EB | Included range sensor malfunction | Use the transmission protection mode. Please contact your dealer. |
T41EE | The curve of transmission parameters in the program | Use the transmission protection mode. Please contact your dealer. |
T41EF | Coupling curve in the program | Please contact your dealer. |
T41FF | Malfunction Autotronic 4 | Please contact your dealer. |
All wheel drive front axle error codes
code | Description | Solution |
T5131 | 4WD switch malfunction | Please contact your dealer. |
T5132 | 4WD switch malfunction | Please contact your dealer. |
T5133 | Fault full electromagnetic valve actuator |
Please contact your dealer. |
T5151 | Differential lock switch malfunction | Please contact your dealer. |
T5153 | Differential lock solenoid valve malfunction | Please contact your dealer. |
T5154 | Left Brake Switch Malfunction | Please contact your dealer. |
T5155 | Malfunction of the switch of the right brake | Please contact your dealer. |
T51FF | Malfunction Autotronic 4 | Please contact your dealer. |
PTO error codes
T6101 | Faulty PTO ON / OFF switch | Please contact your dealer. |
T6102 | Malfunction of the PTO ON / OFF switch located on the wing |
Please contact your dealer. |
T6104 | Malfunction of the PTO solenoid valve | Please contact your dealer. |
T6105 | Malfunction of the PTO clutch speed sensor | Please contact your dealer. |
T6110 | Malfunction of the PTO shaft speed sensor | Please contact your dealer. |
T6115 | Malfunction of the neutral switch on the PTO control unit | Please contact your dealer. |
T6116 | Malfunction of the switch of the speed range of 540 rpm on the PTO control unit |
Please contact your dealer. |
T6117 | Malfunction of the ECO speed range switch on the PTO control unit |
Please contact your dealer. |
T6118 | Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit |
Please contact your dealer. |
T611A | Malfunction of the solenoid valve of the speed range of 540 rpm | Please contact your dealer. |
T611B | Malfunction of the ECO PTO speed solenoid valve | Please contact your dealer. |
T611C | Malfunction of the solenoid valve of the speed range of 1000 rpm | Please contact your dealer. |
T6141 | Faulty PTO ON / OFF switch | Please contact your dealer. |
T6143 | Malfunction of the PTO ON / OFF switch located on the wing |
Please contact your dealer. |
T6145 | Malfunction of the PTO clutch speed sensor | Please contact your dealer. |
T6150 | Malfunction of the PTO shaft speed sensor | Please contact your dealer. |
T6155 | Malfunction of the neutral switch on the PTO control unit | Please contact your dealer. |
T6156 | Malfunction of the switch of the speed range of 540 rpm on the PTO control unit |
Please contact your dealer. |
T6157 | Malfunction of the ECO speed range switch on the PTO control unit |
Please contact your dealer. |
T6158 | Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit |
Please contact your dealer. |
T6160 | Malfunction of the PTO shaft speed sensor Malfunction of the PTO clutch speed sensor |
Please contact your dealer. |
T61A1 | Faulty PTO ON / OFF switch | Please contact your dealer. |
T61B5 | Malfunction of the neutral switch on the PTO control unit | Please contact your dealer. |
T61B6 | Malfunction of the switch of the speed range of 540 rpm on the PTO control unit |
Please contact your dealer. |
T61B7 | Malfunction of the ECO speed range switch on the PTO control unit |
Please contact your dealer. |
T61B8 | Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit |
Please contact your dealer. |
Hydraulic valve error codes
T011493
Reading the error code number.
The code consists of a letter and three numbers.
For example V149:
– V = hydraulic valve
– 1 = number of faulty valve
– 49 = error code number
code | Description | Consequences | Solution |
V.43 | Malfunction of the valve position sensor line | – When an error code appears , a “beep” is heard. – Error code on the display Instrument panel control unit – All valves locked |
– Delete the error code from the control unit of the instrument panel – Unlock the valves (the valve affected by the error code remains blocked). – To reactivate the valve affected by the error code , stop and restart the engine. If the error code is still present, the valve affected by the error code remains blocked. – Contact your dealer. |
V.49 | Main valve does not return to neutral position |
– No – Error code on the display Instrument panel control unit |
– Delete error code from Instrument panel control unit – Contact your dealer. |
V.52 | When starting, the main valve is not in neutral | – No – Error code on the display Instrument panel control unit |
– Delete error code from Instrument panel control unit – Contact your dealer. |
Press the button (16) to clear the error code on the instrument panel control unit display. on keyboard
Multifunction error codes armrest
01 | Output signal error 10 V. Autotronic armrest 5. |
Please contact your dealer. |
eleven | FingerTIP 1 – short circuit to 0 V. | Please contact your dealer. |
12 | FingerTIP 1 – short circuit to 12V. | Please contact your dealer. |
21 | FingerTIP 2 – short circuit to 0 V. | Please contact your dealer. |
22 | FingerTIP 2 – short circuit to 12V. | Please contact your dealer. |
31 | FingerTIP 3 – short circuit to 0 V. | Please contact your dealer. |
32 | FingerTIP 3 – short circuit to 12V. | Please contact your dealer. |
41 | FingerTIP 4 – short circuit to 0 V. | Please contact your dealer. |
42 | FingerTIP 4 – short circuit to 12V. | Please contact your dealer. |
51 | FingerTIP 5 – short circuit to 0 V. | Please contact your dealer. |
52 | FingerTIP 5 – short circuit to 12V. | Please contact your dealer. |
61 | FingerTIP 6 – short circuit to 0 V. | Please contact your dealer. |
62 | FingerTIP 6 – short circuit to 12V. | Please contact your dealer. |
71 | Throttle position control handle – short circuit to 0 V. |
Please contact your dealer. |
72 | Throttle position control handle – short circuit to 12V. |
Please contact your dealer. |
81 | Rear linkage height adjusting wheel – short circuit to 0 V. |
Please contact your dealer. |
82 | Rear linkage height adjusting wheel – short circuit to 12V. |
Please contact your dealer. |
91 | Transmission lever – short circuit to 0 V. | Please contact your dealer. |
92 | Transmission lever – short circuit to 12V. | Please contact your dealer. |
6 | One or more indicator lights are missing | Install indicator bulbs where they are missing. |
7 | Keyboard not connected | Please contact your dealer. |
eight | Checksum error | Please contact your dealer. |
9 | CAN communication problem | Please contact your dealer. |
10 | Short circuit in the front roof lights | Please contact your dealer. |
eleven | Short circuit in the tail lights on the roof | Please contact your dealer. |
12 | Short circuit in brake lights | Please contact your dealer. |
thirteen | Reversing light short circuit | Please contact your dealer. |