KUBOTA Excavator Fault Codes DTC

Service technicians have no problem recognising breakdowns and carrying out machine diagnostics, KUBOTA Excavator Fault Codes DTC, plus they are familiar with equipment from a variety of manufacturers.

Kubota Corporation, is a tractor and heavy equipment manufacturer based in Osaka, Japan in 1960. The company roots trace back to 1890, when it manufactured cast iron water pipes.

The company produces many products including:

  • Tractors and Agricultural Equipment;
  • Engines;
  • Construction Equipment;
  • Vending machines;
  • Pipe;
  • Valves;
  • Casting;
  • Pumps;
  • Equipment for Water purification and Sewage Treatment;
  • Air Conditioning Equipment.


data000 This LCD display shows the following conditions; fuel amount, water temp., engine oil pressure, battery, glow plug, and operating hour meter.
data001 This LCD display shows the following conditions; fuel amount, water temp., engine speed.
data002 This LCD display shows the following conditions; fuel amount, water temp., and operating hour meter.
data003 The letter on the LCD indicates the warning of each function;fuel amount shortage
data004 The letter on the LCD indicates the warning of low engine oil pressure
data005 The letter on the LCD indicates the warning of low charging voltage of alternator
data006 The letter on the LCD indicates the warning of each function; higher voltage line connected for example, 24 V battery
data007 The letter on the LCD indicates the warning thepossibility of engine overheating condition EU – version only : 124 ± °C
data008 The letter on the LCD indicates the warning ofaccel sensor line break or shortage
data009 The letter on the LCD indicates the warning of governor sensor line break or shortage
data010 The letter on the LCD indicates the warning of AI motor line shortage.
data011 The letter on the LCD indicates the warning of AI motor line break.
data012 The letter on the LCD indicates the amount of auxiliary port flow.
data013 The letter on the LCD indicates the warning of electrical shortage of aux. solenoid valve left side.
data014 The letter on the LCD indicates the warning of electrical line break of aux. solenoid valve left side.
data015 The letter on the LCD indicates the warning of electrical shortage of aux. solenoid valve right side.
data016 The letter on the LCD indicates the warning of electrical line break of aux. solenoid valveright side.
data017 The letter on the LCD indicates the warning of coolant sensor or water temp. sensor fail.
data018 The letter on the LCD indicates the warning of fuel sensor fail.
data019 The letter on the LCD indicates the warning of 12V sensor supply line shortage.
data020 The letter on the LCD indicates the warning of 5V sensor supply line shortage.
data021 The letter on the LCD indicates the warning of controller error in the meter panel.
data022 The letter on the LCD indicates the warning of AI motor being restricted by any means.
data082 These indicates where machine was manufactured.
data084 This indicates that operator is suggested to lift up

E:001 The Controller Area Network (CAN) has developed a fault. Measured values may be incorrect and switches may not function. The machine can be started and driven. Do not perform any work with the machine.
E:005 The temperature of the coolant is higher than normal. Operate the machine only with reduced loads until the temperature is normal again.
E:014 The engine oil pressure is too low. Stop the engine immediately. The engine may have developed a fault. Inform your KUBOTA dealer immediately.
E:015 The machine is overheated and must cool off by idling. Allow the machine to cool off by idling. Do not switch the engine off as the coolant could then boil over. Clean the radiator and check the coolant. Refi ll the radiator with coolant by its boiled-over amount. Unclog the radiator and other components before use again. Check also the hydraulic system for oil leak and other troubles. If an oil leak is found, immediately contact your local dealer for repair.
E:016 The charging system has developed a fault. Check the V-belt. When the V-belt is OK, let the engine run until the indicator goes out. If the indicator does not go out, inform your KUBOTA dealer immediately.
E:017 The fuel sensor has developed a fault; the fuel gauge does not appear in the display. Press the display selector switch to return to the default display.
E:018 The coolant temperature sensor has developed a fault; the coolant temperature gauge does not appear in the display. Press the display selector switch to return to the default display. The functions of the machine are stable but overheating cannot be excluded.
E:020 The electrical system in the lock lever (unload lever) has developed a fault. The engine can be started but the machine cannot be set in motion.
E:021 The electrical system in the travel speed has developed a fault. The machine can only be set in motion at low speed.
E:025 This is a warning that a higher volt- age (from a 24-V battery, for example) is being applied to the electric circuit, or that there is a problem with the alternator. Switch the engine off immediately and check the battery and the alternator. Restart the engine.
E:027 The 5-V sensor supply line has de- veloped a system fault. The main functions are not available. The machine can be started and driven. Do not per- form any work with the machine.
E:028 The 12-V sensor supply line has de- veloped a system fault. The main functions are not available. The machine can be started and driven. Do not per- form any work with the machine.
E:029 This error code indicates a step in a procedure. Start the engine; the indicator goes out.

The diagnosis tool KUBOTA Excavator Fault Codes DTC for trucks provides different possibilities such as information on the use and location of the connectors, detection and description of errors, activation of the fan, compression test and other components, system data information and more.